View LQ065T5AR01_161150.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

www..com
LQ065T5AR01
Color TFT LCD Module
(Model Number: LQ065T5AR01)
Specifications
Spec No.: LCY-01096B Dated: May 31. 2002
DataSheet 4U .com
www..com
PREPARED BY:
DATE
SPEC No. FILE No.
LCY-01096B
APPROVED BY:
DATE
MOBILE LIQUID CRYSTAL DISPLAY GROUP SHARP CORPORATION
ISSUE:
Jan. 24. 2002
PAGE : 29 pages
APPLICABLE GROUP LIQUID CRYSTAL DISPLAY GROUP
SPECIFICATION
DEVICE SPECIFICATION FOR
TFT - LCD
MODEL No.
module
LQ065T5AR01
CUSTOMER'S APPROVAL
DATE PRESENTED BY BY S.YASUDA Department General manager Engineering department Mobile LCD design cener MOBILE LIQUID CRYSTAL DISPLAY GROUP SHARP CORPORATION
DataSheet 4U .com
www..com
RECORDS OF REVISION
SPEC No.
REVISED No.
DATE
SUMMARY PAGE add a postscript(Fig.7) change temperature of Absolute maximum ratings.(Ta=25-30+85) 15,19 change protection film 16 19 correct a error word(Fig.7Fig.8) add a postscript(depth of mounting hole) change PWB for improve of coupling issue (DUNTK2959TPZZ DUNTK3028TPZZ)
NOTE
LCY-01096 2001.11. 9. 2001.12.18 A
1 st Issue
3 8
2002.01.24
B
-
DataSheet 4U .com
www..com
LCY010961
NOTICE
This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any purpose, in whole or in part, without the express written permission of SHARP. Express written permission is also required before any use of this publication may be made by a third party. The application circuit examples in this publication are provided to explain the representative applications of SHARP's devices and are not intended to guarantee any circuit design or permit any industrial property right or other rights to be executed. SHARP takes no responsibility for any problems related to any industrial property right or a third party resulting from the use of SHARP's devices, except for those resulting directly from device manufacturing processes. In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP's device. SHARP reserves the right to make changes in the specifications, characteristics, data, materials, structures and other contents described herein at any time without notice in order to improve design or reliability. Contact SHARP in order to obtain the latest specification sheets before using any SHARP's device. Manufacturing locations are also subject to change without notice. Observe the following points when using any device in this publication. SHARP takes no responsibility for damage caused by improper use of the devices. The devices in this publication are designed for use in general electronic equipment designs,such as: Car Navigation system Automotive auxiliary information display Automotive audio visual equipment The appropriate design measures should be taken to ensure reliability and safety when SHARP's devices are used for equipment such as: Transportation control and safety equipment(i.e.,aircraft,trains,automobiles,etc.) Traffic signals Gas leakage sensor breakers Alarm equipment Various safety devices etc. SHARP's devices shall not be used for equipment that requires extremely high level of reliability, such as: Military and space applications Nuclear power control equipment Medical equipment for life support Contact a SHARP representative, in advance, when intending to use SHARP's devices for any "specific" applications other than those recommended by SHARP. Contact and consult with a SHARP representative if there are any questions about the contents of this publication.
DataSheet 4U .com
www..com
LCY010962
CONTENTS
Introduction Features Construction and Outline Module geometry Absolute maximum ratings Electrical characteristics Optical characteristics Mechanical characteristics 10 Display quality 11 Mechanical Noise 12 Handling instruction 13 Shipping requirements 14 Reliability test conditions 15 Others
Page ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. ............................................. 12 13 15 15 16 17 17
Input/Output symbol and description .............................................
............................................. 15
Attached Figures Fig 1Outline dimension of TFT-LCD module Fig 2Circuit block diagram of TFT-LCD module Fig 3Recommended circuit to be refered FigInput/Output signal waveforms FigOptical characteristics FigClock and Video signal timing (Reference) FigConstruction of TFT-LCD module FigPacking form
..................... 19 ..................... 20 ..................... 21 ..................... ..................... ..................... ..................... 22 26 27 28
..................... 29
DataSheet 4U .com
www..com
LCY010963
(1) Introduction The SHARP color TFT-LCD module is an active matrix LCD (Liquid Crystal Display) produced by making the most of Sharp's expertise in liquid-crystal and semiconductor technologies. The active device is amorphous silicon TFT (Thin Film Transistor). The module has a 16:9 aspect ratio and accepts full color video signal conforming to the NTSC and PAL systems. An outline of the module is shown in Table 1. (2) Features 16:9 aspect ratio suitable for the wide-screen systems. a variety of display modes can be selected without any loss of wide-screen characteristics The 6.5 screen produces a high resolution image that is composed of 93,600 pixel elements in a stripe arrangement. Wide viewing angle technology is adopted. (The direction which has earlier inversion of gray scale image 6 o'clock direction.) External clock synchronization allows an extremely clear image to be displayed. TFT-active matrix-LCD drive system with high contrast Dual mode type [NTSC (M) and PAL(BG) standards] MBK-PAL which enables the 234-scanning lines panel to display a picture with virtually 274scanning lines. Reduced reflection as a result of low reflectance black matrix and an antiglare (AG) and antireflection (R) polarizer being adopted. A thin, lightweight and compact Effective area/Outline area= 82% Thickness= 16.0 mmMass= 240g(max) Through the use of TN-normally white mode, an image with highly natural color reproduction is realized. It is possible to reverse the display direction (rightleft and updown). Semi Self-heating Backlight that is excellent of brightness rising characteristics at low temperature in consideration of automotive application (3) Construction and Outline Outline dimension of TFT-LCD module : Fig. The module consists of the TFT-LCD panel, driver ICs, control PWB mounted with electronic circuits, semi self-heating backlight, frame, inverter, DC/DC for single supply voltage, front and rear shielding cases.:Fig.7
(4)Module geometry(Mechanical specifications) Table 1 Parameter Specifications Display format 93,600 1200(W)x234(H) Active area 143.4Wx79.326H Screen size (Diagonal) 16.5 [6.5"] Dot pitch 0.1195Wx0.339H Pixel configuration R,G,B Stripe configuration Outline dimension 155(W)x89.2(H)x16.0(D) Mass 240 Note4-1This measurement is typical,and see Fig .1 for the details.
Units pixels dots mm cm mm mm
Remarks
Note4-1 Max
DataSheet 4U .com
www..com
LCY010964
(5)Input/Output terminal and their descriptions 5-1)TFT-LCD panel driving section Table 2 (Hi and Lo means digital input voltage Pin No. Symbol i/o Description Remarks TEST Selection for input/output direction of Note5-1 HSY,VSY, CLK+,CLK Input/Output horizontal sync. signal (low active) Note5-2 Note5-3 Input/Output vertical sync. signal (low active) Timing signal for PWM dimming of backlight Note5-4 Selection for NTSC or PAL Note5-5 Selection for horizontal scanning direction Note5-6 Selection for vertical scanning direction Note5-7 Selection for display mode Note5-8 Selection for display mode Note5-8 Note5-8 Selection for display mode Positive power supply voltage Composite sync.signal (low active) Note5-9 Note5-10 Brightness adjusting terminal Positive (On when Color video signal (Red) VSW=Hi.) Ditto Color video signal (Green) Ditto Color video signal (Blue) Ground Positive (On when Color video signal (Red) VSW=Lo.) Ditto Color video signal (Green) Ditto Color video signal (Blue) Ground Clock signal (LVDS) Note5-11 Clock signal (LVDS) Note5-11 Note5-12 Selection signal of two sets of video signals Note5-13 Input signal for backlight dimming Power supply for BackLight Power supply for BackLight Ground for BackLight Ground for BackLight
Note5-1 Note5-2 Note5-3 Note5-4
Note5-5 Note5-6 Note5-7 Note5-8 Note5-9
CLKC = "Hi": HSY and VSY terminals are the output mode. CLKC = "Lo": CLK,CLK, HSY and VSY terminals are the input mode. If CLKC="Hi", this terminal outputs horizontal sync. signal in phase with VBS. If CLKC="Lo", this terminal will be external horizontal sync. input terminal. If CLKC="Hi", this terminal outputs vertical sync. signal in phase with VBS. If CLKC="Lo", this terminal will be external vertical sync. input terminal. PWM signal is used for the PWM dimming frequency and it is possible to control the PWM signal dimming by combining both HSY and PWM signal. But, please use this PWM signal just in case of inputting standard NTSC or PAL signal. NTP = "Hi": NTSC system NTP = "Lo": PAL system HRV = "Hi": Normal video HRV = "Lo": Reversed video on horizontal direction VRV = "Hi": Normal video VRV = "Lo": Reversed video on vertical direction Display mode settings are shown in Table 3. The sync. Signal which will be input, is negative polarity, and is applicable to standard composite sync. signal, negative one, in the same pulse level.
DataSheet 4U .com
www..com
LCY010965
Note5-10 Brightness is adjusted by the DC voltage supplied to this pin. They are adjusted to the optimum value on shipping, but, they can be re-adjusted by external circuit. When CLKC="Lo", this terminal will be external clock input terminal. This signal should correspond to sampling timing of the horizontal direction image. NTP, MODS, MODW, and MODN should be "Hi" when CLKC="Lo". When VSW="Hi", CH1 (VR1, VG1, VB1) is selected. When VSW="Low", CH2 (VR2, VG2, VB2) is selected. The signal of PWMI is used for control of ON/OFF switch of backlight. When PWMI="Hi", the backlight is lighted. When PWMI="Low", the backlight puts the light out.
And, PWMS signal is used for the PWMI dimming frequency and it is easy to get PWM signal dimming by combining both HSY and PWMS signal. But please use this PWMS signal just in case of inputting standard NTSC or PAL signal.
Note5-11
Note5-12 Note5-13
DataSheet 4U .com
www..com
LCY010966 Display Method and Characteristics Table 3 MODS MODW MODN Display Characteristics Source example mode H H H Full 4:3 signal, Fig.3)-1 The picture is displayed with uniform mode Navigation enlargement in the horizontal direction, and the horizontal retrace line of the input signal signal cannot be seen. If the video sampling frequency of the image is fixed and a 4:3 video signal is displayed, the picture will be prominently oblong. 4:3 signal A 4:3 video signal is displayed with less feeling of incongruity than that in the full screen mode. Since the video horizontal sampling frequency is modulated in the horizontal direction, the degree of perfect roundness in the center of the screen is improved over that of the full screen mode. 4:3 signal When displaying a 4:3 video signal, the displayed image is slightly less than perfectly round and the horizontal retrace line period is displayed at the two edges of the screen. With respect to the video horizontal sampling frequency, the center portion of the screen is slightly lower and the two edges become slightly higher. letter box A letter-box type image (16:9 signal) is type wide displayed over the central width of the signal(16: screen. In the horizontal direction, full 9signal) screen display is utilized. Due to the display being extended in the vertical direction, a slightly less than perfectly round image is displayed. 4:3 signal In the horizontal direction, the Wide 1 display mode is employed. Due to the display being extended in the vertical direction, the portion of the picture in the center of the screen is slightly less than perfectly round. Also due to extending in the vertical direction, the upper and lower potions of the image are not displayed. This mode is unusable as it is the test mode. This mode is unusable as it is the test mode. This mode is unusable as it is the test mode.
H
H
L
Wide 1 mode
Fig.3)-2
H
L
H
Normal mode
Fig.3)-3
H
L
L
Cinema mode
Fig.3)-4
L
H
H
Wide 2 mode
Fig.3)-5
L L L
H L L
L H L
test test test

DataSheet 4U .com
www..com
LCY010967
Fig.3)-1
Full mode
Fig.3)-2
Wide 1 mode
Fig.3)-3
Normal mode
Fig.3)-4
Cinema mode
Fig.3)-5
Wide 2 mode
DataSheet 4U .com
www..com
LCY010968
5-2)Functions, Modes and TerminalsTable Mode terminals Sync,signal I/O terminals Remarks , CLKC NTP MODS MODW MODN H H or L H L H sync. V sync. Composite test mode L L L H output output sync. input L L L H H or H L H H sync. V sync. Composite NTSC or PAL mode L output output sync. input (Normal mode) Composite NTSC or PAL mode H H or other H or L H sync. V sync. sync. input (Full,Wide,Cinema L settings output output LH H H H H sync. V sync. Pixel input Hi or External clock input input clock Lo fixed synchronous mode input value
(6) Absolute maximum ratings Table 5 -30+85 Parameter Symbol Unit Note -0.3 9.0 Positive power supply voltage Positive power supply voltage -0.3 9.0 Analog Input signals 2.0 Vp-p [terminal 6-1] -0.3 5.3 Digital Input signals [terminal 6-2] -0.3 5.3 Digital Output signals [terminal 6-3] LVDS Input signals LIS -0.3 5.3 [terminal 6-4] Brightness adjusting voltage VBRT 5.0 Storage temperature -40 85 stg Note 6-1,2 -30 85 Operating temperature Note 6-2,3,4 opr1 panel surface -30 65 Operating temperature Note 6-4,5 opr2 Ambient temperature [terminal 6-1] terminals(Video signal) [terminal 6-2] terminals [terminal 6-3] terminals [terminal 6-4] CLK,CLK+ terminals
Note 6-1 Note 6-2
Note 6-3 Note 6-4
Note 6-5
This rating is applied to all parts of the module and should not be exceeded. Maximum wet-bulb temperature is less than 58. Condensation of dew must be avoided as electrical current leaks will occur, causing a degradation of performance specifications. Please measure in the effective display area only. The operating temperature only guarantees operation of the circuit. For contrast, speed response, and other factors related to display quality, determine operating temperature using the formula Ta=25 Ambient temperature when the backlight is lit (reference value).
DataSheet 4U .com
www..com
LCY010969
(7) Electrical characteristics 7-1)Recommended operating conditions A)TFT-LCD panel driving section Table 6 Parameter Symbol Power supply voltage +7.2 +7.2 Power supply voltage Power supply voltage rising time VIN 0.7 Analog Amplitude Input voltage VI VIDC -1.0 component VIH +3.5 Digital Input voltage VIL 0 Histeresis VH +0.2 VOH +4.0 Digital output voltage VOL 0 LVDS Differential VTH Input signal Input High Threshold Differential VTL Input Low 100 Threshold frequency fCLI 7.2 Input horizontal frequency NTSC fH(N) 15.13 sync. signal PAL fH(P) 15.03 4.2 pulse NTSC HI(N) width PAL 4.2 HI(P) rising time rHI1 falling time fHI1 Input vertical fV(N) fH/284 frequency NTSC sync. signal PAL fV(P) fH/344 pulse NTSC VI(N) width PAL VI(P) rising time rVI falling time fVI Input horizontal frequency fHI fCLI/550 sync. signal pulse width 1 HI rising time rHI2 falling time fHI2 Input vertical frequency fVI 50 sync. signal pulse width 1H VI Data setup time tSU1 24 Data hold time tHO1 44 Data setup time tSU2 1.0 Data hold time tHO2 1.0
opr13085 Remarks Unit +8.0 +8.5 V +8.0 +8.8 V 60 ms Note 7-1 1.0 2.0 Vp-p 0.7 Vp-p Note 7-2 0 +1.0 V Note 7-3 +5.0 V Note 7-4 +0.5 V V +5.0 V Note 7-5 +1.0 V CLKC="Lo" +100 mV Note 7-6 mV 8.0 15.73 15.63 4.7 4.7 fH/262.5 fH/312.5 3H 2.5H fCLI/508 5 fHI/262 3H 8.8 MHz 16.33 kHz CLKC=`Hi' 16.23 kHz Note 7-7 5.2 s 5.2 s 0.5 s 0.5 s fH/258 Hz CLKC=`Hi' fH/304 Hz Note 7-8 s s 0.5 s CLKC=`Hi' or `Lo' 0.5 s fCLI/490 kHz CLKC=`Lo' 9 s Note 7-9 0.05 s 0.05 s fHI/258 Hz CLKC=`Lo' Note 7-10 5H s ns CLKC=`Lo' ns Note 7-6,9,11 s CLKC=`Lo' s Note 7-6,10,12
Caution: Signals must input after power has been turned on.
Note 7-1
7.2V
0.6V
DataSheet 4U .com
www..com
LCY0109610 Note 7-2 terminals (Video signal) Note 7-3 terminals Note 7-4 terminals Note 7-5 terminals Note 7-6 CLK,CLK+ (DS90C402 : LVDS Receiver made by National Semiconductor) ( Adaptation LVDS Transmitter : DS90C401) Note 7-7 (horizontal sync. component) terminal Note 7-8 (vertical sync. component) terminal Note 7-9 terminal Note 7-10 terminal Note 7-11During the clock input mode, CLK,CLK+ and the HSY input signal are out of phase. In this mode, the HSY input signal is effected by the rise time of the CLK+ input signal. Note 7-12 During the clock input mode, HSY and the VSY input signal are out of phase. In this mode, the VSY input signal is effected by the rise time of the HSY input signal.
7-2)Power consumption Table 7
Parameter Positive supply current Positive supply current Total Symbol IIN IBL Conditions VIN=8.0V VBL=8.0V 160 750 7.28 210 950 9.20 Unit mA mA W -30+85 Remarks
7-3)Input/Output signal timing chart Table 8 VIN=+8.0,GND=0V Parameter Horizontal sync. frequency Output pulse width rising time falling time Horizontal sync. HSY falling phase difference time HSY rising time Vertical sync. frequency Output pulse width sync. output difference rising time falling time Vertical sync. odd field Phase Difference even field
CLKC=Hi NTSC:fH=15.73kHz,fv=60Hz,HI=4.7s PAL:fH=15.63kHz,fV=50Hz,HI=4.7s Symbol MIN TYP MAX Unit fHO fH kHz HO rHO fHO pd1 pd2 fVO VO VHO rVO fVO DV1 DV2 2.0 0.5 4.6 1.6 1.6 Fv 4H 11 1H 0.5H 8.0 0.5 0.5 3.0 3.4 29 2.0 2.0 s s s s
Remarks
Note 7-13 CL=10pF CL=10pF Note 7-14
-
s Hz s 1H=1/fH s s CL=10pF s CL=10pF s
td 40 65 90 ns Note7-15 Clock and Video signal timing Reference value Note7-13 This is changed by the value of pd1 Note7-14 Center position : pd1= 1.60.4 (NTSC mode) Note7-15 Clock and Video signal timing : Fig.6
DataSheet 4U .com
www..com
LCY0109611
7-4) Display time range (1) NTSC(M) mode (NTP='Hi',CLKC='Hi') (a1) Horizontal Direction (full,wide1,2,cinema) 13.1 63.2 s from the falling edge of HSY. (a2) Horizontal Direction (normal) 8.0 68.3 s from the falling edge of HSY (b1) Vertical Direction (full,wide1,normal) 20 253 H from the falling edge of VSY (b2) Vertical Direction (Cinema) 49 224 H from the falling edge of VSY (b3) Vertical Direction (Wide2) 42 228 H from the falling edge of VSY (2)PAL(BG) mode (NTP='Lo',CLKC='Hi') (a1) Horizontal Direction (full,wide1,2,cinema) 13.3 63.2 s from the falling edge of HSY (a2) Horizontal Direction (normal) 8.1 68.4 s from the falling edge of HSY. (Normal) (b1) Vertical Direction (full,wide1,normal) 26 298 H from the falling edge of VSY However, the video signals of (14n+12)H,(14n+20)H/Even field. (14n+17)H,(14n+23)H/Odd field (n=1,2, 20) are not displayed on the module. (b2) Vertical Direction (cinema) 49 282 H from the falling edge of VSY (b3) Vertical Direction (wide2) 35 291 H from the falling edge of VSY However, the video signals of (22n+14)H,(22n+21)H/Even field. (22n+25)H,(22n+32)H/Odd field (n=1,2, 12) are not displayed on the module. (3) External clock mode (NTP='Hi',CLKC='Lo') Displaying the following range within video signals. (a) Horizontal Direction : 86 485 clk from the falling edge of HSY. (clk means input external clock.) (b) Vertical Direction : 20 253H from the falling edge of VSY. 7-5)Backlight driving section Usable area for Backlight lighting PWM Dimming Duty=100%5% (Please use this PWMS signal just in case of inputting standard NTSC or PAL signal) DC/AC inverter driving frequency = 65kHz (reference value)
DataSheet 4U .com
www..com
LCY0109612
(8)Optical characteristics Table 9 Parameter Viewing angle range Contrast ratio Response Rise time Fall Luminance White chromaticity VIN=+8.0VVBL=+8.0V Ta=25 Typ Max Unit Remarks 65 (degree) Note8-1,2,3 40 (degree) 65 (degree) Note8-1,3 60 100 0.363 0.379 ms ms cd/m2 Note8-1,4 Note8-1,5 Note8-1,5 Note8-1,6 Note8-1,7
Symbol 11 12 2 CRmax
Condition CR Optimal viewing angle
Min 60 35 60 60
30 r 50 d Y 315 420 x 0.263 0.313 y 0.279 0.329 Lamp life +25 Continuation 10,000 time Intermission 2,000 -30 Applied voltage condition for the measurement Bright adjustment voltage (BRT) to be opened Video signal of standard black level and 100% white level Note 8-1Measuring method : Fig.5 Note 8-2Viewing angle range is defined as follows.
hour time
Normal line 2 11 12 2
6 o'clock direction
definition for viewing angle Note 8-3 Contrast ratio is defined as follows: Photodetector output with LCD being "white" Contrast ratio = Photodetechor output with LCD being "black" Response time is obtained by measuring the transition time of photodetector output, when input signals are applied so as to make the area "black" to and from "white".
Note 8-4
DataSheet 4U .com
www..com
LCY0109613
White Photodetecter output (arbitrary unit) Time Black White
Note 8-5 Note 8-6
Note 8-7
Measured on the center area of the panel at a viewing cone 1 by TOPCON luminance meter BM-7.(After 30 minutes operation) Lamp life time is defined as the time when brightness not to become under 50% of the original value in the continuous operation under the condition of PWM dimming duty 100%5% (Ta=25). The intermittent cycles is defined as a time when brightness not to become under 50% of the original value under the condition of following cycle. Ambient temperature:-30
ON
OFF 5min 5min 5min 5min
(9)Mechanical characteristics 9-1) External appearance Extreme defects should not exist. (See Fig. 1) 9-2) Panel toughness The panel shall not be broken,when 19N is pressed on the center of the panel by a smooth sphere having 15 mm diameter. Caution: In spite of very soft toughness, if, in the long-term, add pressure on the active area, it is possible to occur the functional damage.
DataSheet 4U .com
www..com
LCY0109614
9-3) Input/output connector performance A)Input/output connectors for the operation of LCD module (30 pinKYOCERA ELCO CORPORATION:6200307032800) 1) Applicable FPC : Refer the below figure 2) Terminal holding force : More than 0.9N/pin. (Each terminal is pulled out at a rate of 25 3mm/min.) 3) Insertion/pulling :contact resistance is not twice larger than the durability initial value after applicable FPC is inserted and pulled out 20 times
31.00.1 0.30.05
1.00.15 (R0.5)
DataSheet 4U .com
6 MIN 5 MIN 1.00.02 0.7 + 0.07 - 0.05
No. 1 2 3 4
Name Base material Copper foil Cover lay Reinforcing plate
Materials Polyimide or equivalent material(25m thick) Copper foil(35m thick) Solder plated over 2 m Polyimide or equivalent material Polyester polyimide or equivalent material(188m thick)
FPC applied to input/output connector (1.0mm pitch)
www..com
LCY0109615
(10) Display quality The display quality of the color TFT-LCD module shall be in compliance with the Incoming Inspection Standard. (11) Mechanical Noise No abnormal mechanical noise which can be easily recognized when the module is shaken by hand. (12) Handling instructions 12-1) Mounting of module The TFT-LCD module is designed to be mounted on equipment using the mounting tabs in the four corners of the module at the rear side. On mounting the module, as the M2.6 tapping screw fastening torque is 0.3 through 0.5Nm is recommended, be sure to fix the module on the same plane, taking care not to wrap or twist the module. Don't reach the pressure of touch-switches of the set side to a module directly, because images may be disturbed. Please power off the module when you connect the input/output connector. 12-2) Precautions in mounting Polarizer which is made of soft material and susceptible to flaw must be handled carefully. Protective film (Laminator) is applied on the surface to protect it against scratches and dirts. It is recommended to peel off the laminator immediately before the use, taking care of static electricity. Precautions in peeling off the laminator A) Working environment When the laminator is peeled off, static electricity may cause dust to stick to the polarizer surface. To avoid this, the following working environment is desirable. a) Floor : Conductive treatment of 1M or more on the tile. (conductive mat or conductive paint on the tile) b) Clean room free form dust and with an adhensive mat on the doorway c) Advisable humidity:50%70% Advisable temperature:1527 d) Workers shall wear conductive shoes, conductive work clothes, conductive gloves and an earth band. B) Working procedures a) Direct the wind of discharging blower somewhat downward to ensure that module is blown sufficiently. Keep the distance between module and discharging blower within 20 cm. b) Attach adhensive tape to the laminator part near discharging blower so as to protect polarizer against flaw. c) Peel off laminator, pulling adhesive tape slowly to your side. d) On peeling off the laminator, pass the module to the next work process to prevent the module to get dust.
D irection of w in d of blow er
d isch argin g blow er m od u le
less th an 2 0cm
in pu t con n ector
A dh esive ta pe
e) Method of removing dust from polarizer * Blow off dust with N2 blower for which static electricity preventive measure has been taken. Ionized air gun (Hugle Electronics Co.) is recommended. * Since polarizer is vulnerable, wiping should be avoided.
DataSheet 4U .com
www..com
LCY0109616
But when the panel has stain or grease, we recommend to use adhesive tape to softly remove them from the panel. When metal part of the TFT-LCD module (shielding lid and rear case) is soiled, wipe it with soft dry cloth. For stubborn dirt, wipe the part, breathing on it. Wipe off water drop or finger grease immediately. Long contact with water may cause discoloration or spots. Since TFT-LCD module uses glass which breaks or cracks easily if dropped or bumped on hard surface, handle with care. Since CMOS LSI is used in this module, take care of static electricity and earth your body when handling. 12-3) Precautions in adjusting module Adjusting volumes on the rear face of the module have been set optimally before shipment. Therefore, do not change any adjusted values. If adjusted values are changed, the specifications described here may not be satisfied. 12-4) Caution of product design The LCD module shall be protected against water salt-water by the waterproof cover. Please take measures to interferential radiation from module, to do not interfere surrounding appliances. 12-5)Mounting direction Mounting direction of the TFT-LCD module to the application needs to be carefully fixed by evaluating display performance. 12-6)Others Do not expose the module to direct sunlight or intensive ultraviolet rays for many hours; liquid crystal is deteriorated by ultraviolet rays. Store the module at a temperature near the room temperature. At lower than the rated storage temperature, liquid crystal solidifies, causing the panel to be damaged. At higher than the rated storage temperature, liquid crystal turns into isotropic liquid and may not recover. The voltage of beginning electric discharge may over the normal voltage because of leakage current from approach conductor by to draw lump read lead line around. If LCD panel breaks, there may be a possibility that the liquid crystal escapes from the panel. Since the liquid crystal is injurious, do not put it into the eyes or mouth. When liquid crystal sticks to hands, feet or clothes, wash it out immediately with soap. Observe all other precautionary requirements in handling general electronic components. (13) Shipping requirements 13-1) Packing form is shown in Fig.8. 13-2) Carton storage condition Number of layers of cartons in pile : 10 layers max. Environmental condition Temperature 0 to 40 Humidity 60 %PH or less (at 40) No dew condition even at a low temperature and high humidity Atmosphere Harmful gases such as acid and alkali which corrode electronic components and wires must not be detected. Storage period About 3 months Opening of package To prevent TFT-LCD module from being damaged by static electricity, adjust the room humidity to 50%PH or higher and provide an appropriate measure for electrostatic earthing before opening the package.
DataSheet 4U .com
www..com
LCY0109617
(14)Reliability test conditions Reliability test conditions for the TFT-LCD module are shown in Table 10. (15)Others 15-1)Indication of lot number The lot number is shown on a label. Attached location is shown in Fig.1(Outline Dimensions). Indicated contents of the label LQ065T5AR01 model No. lot No.
figure production year (ex.1999 : 9) Contents of lot No. the 1st figure production month 1,2,3,......,9,X,Y,Z the 2nd the 3rd~8th figure serial No. 00001 figure revision marks blank or A,B,C ... the 9th the 10th figure production factory code blank or A,B,C ...
DataSheet 4U .com
www..com
LCY0109618
Reliability test conditions for TFT-LCD module Table 10 Remark) Temperature condition is based on operating temperature conditions on (6)-Table 5 No. Test items Test conditions 1 High temperature Ta=+85 240h storage test 2 Low temperature Ta=-40 240h storage test 3 High temperature Ta=+60, 90%RH 240h And high humidity operating test 4 High temperature Tp=+85Ta=+65 240h operating test 5 Low temperature Ta=-30 240h operating test 6 Electro static 200V, 200pF(0) 1 times for each terminals discharge test 7 Shock test 980m/s6ms, X, Y, Z 3times for each direction (JIS C0041,A-7 condition C) Vibration test 8 Frequency range : 833.3Hz Stroke : 1.3mm Sweep : 33.3Hz400Hz Acceleration : 28.4 m/s Cycle : 15 minutes X,Z 2 hours for each directions, 4 hours for Y direction (total 8 hours) caution (JIS D1601) 9 Heat shock test Ta=-30+85 / 200cycles storage test (0.5h) (0.5h) NoteTa=Ambient temperature, Tp=Panel temperature Check itemsIn the standard condition, there shall be no practical problems that may affect the display function. CautionX,Y,Z directions are shown as follows
DataSheet 4U .com
www..com
LCY01096-19
Fig.1
Outline dimensions of TFT-LCD module
DataSheet 4U .com
DataSheet 4U .com
www..com
Power supply circuit
+8.0V
1 2 VIN
CLKC
Gate driver
HSY VSY
Gate driver driving signal
NTP
Control circuit
Source driver driving signal
HRV VRV MODS,MODW, ,MODW,MODN 1 0 11 MODS ,MODW, MODN
Source driver
LVDS Receiver
24 CLK+
CLK23 CLK25 VSW
.
13 VBS
Common electrode driving signal
Common electrode driving signal circuit
Video interface circuit

14 BRT 15 16 17 VR1,VG1,VB1 1 9 20 21 VR2,VG2,VB2 26
LCD driving signal
PWMS PWMI
VBL
LCY0109620
Backlight driving signal Backlight Fig.2
Backlight driving circuit
+8.0V
27 28
Circuit block diagram of the module
www..com
DataSheet 4U .com
DataSheet 4U .com
www..com
3(NTSC) 2.5(PAL)
16.7ms(NTSC) 20.0ms(PAL)
odd field
even field
1.0Vp-p
pv1
pv2
detailed VS rVO fvo
VSY HSY
VHO
VHO
fHO Vertically display period
rHO
VIDEO LCY01096-22 (R,G,B
0.7Vp-p
Fig.4A Input / Output signal waveforms(CLKC="Hi")
DataSheet 4U .com
www..com
VBS
HS1
1H=63.5s(NTSC) 1H=64.0s(PAL)
pd
10%
HSY
50% 90% fHO HS2 rHO
Horizontally display area
Video signal VR1VB1 or VR2VB2 LCY01096-23
Fig.4B Input/Output signal waveforms (CLKC="Hi")
DataSheet 4U .com
CLK+ CLK
tH O 1 tS U 1
www..com
fH I2 HI rH I2
rV O fV O
tH02
tSU2
LCY01096
-24
1H
Fig. 4C
Input/Output signal waveforms (external clock mode
NTP="Hi", CLKC="Lo")
DataSheet 4U .com

www..com
PW M S (N T S C )
PW M S (P A L )
m a g n ify tim e r a n g e
VSY

HSY

PW M S

LCY01096-25
PW M I
in v e r te r o s c illa tio n n o in v e r te r o s c illa tio n
Fig. 4-D PWM dimming timing
www..com
LCY0109626
Photodetector (including luminosity factor)
TFT-LCD module
LCD panel
Center
Fig. 5 Measuring method of optical characteristics
DataSheet 4U .com
www..com
LCY0109627 Reference Clock and Video signal timing [Input Condition] DotClock frequency Hsyn. frequency Vsyn. Frequency Video Signal CLK = 8.0MHz fH15.748kHz fV60.107Hz Cross-Hatching (To show white lines every 24 dots with the background display of Balck) Amplitude = 0.7Vpp TVrTVf17ns TVH125ns
CLK -
CLK + white level
d
Input Video
0.7Vpp
TVH125ns
black level
TVf
TVr
White Vertical Line
Fig.6 Clock and Video signal timing
DataSheet 4U .com
www..com
LCY01096-28
Fig.7 Construction of TFT-LCD module
DataSheet 4U .com
www..com
LCY01096-29
Fig.8 Packing form
DataSheet 4U .com
www..com
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited Warranty for SHARP's product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or in any way responsible, for any incidental or consequential economic or property damage.
NORTH AMERICA
EUROPE
JAPAN
SHARP Microelectronics of the Americas 5700 NW Pacific Rim Blvd. Camas, WA 98607, U.S.A. Phone: (1) 360-834-2500 Fax: (1) 360-834-8903 Fast Info: (1) 800-833-9437 www.sharpsma.com
SHARP Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com
SINGAPORE
SHARP Corporation Electronic Components & Devices 22-22 Nagaike-cho, Abeno-Ku Osaka 545-8522, Japan Phone: (81) 6-6621-1221 Fax: (81) 6117-725300/6117-725301 www.sharp-world.com
TAIWAN
KOREA
SHARP Electronic Components (Taiwan) Corporation 8F-A, No. 16, Sec. 4, Nanking E. Rd. Taipei, Taiwan, Republic of China Phone: (886) 2-2577-7341 Fax: (886) 2-2577-7326/2-2577-7328
SHARP Electronics (Singapore) PTE., Ltd. 438A, Alexandra Road, #05-01/02 Alexandra Technopark, Singapore 119967 Phone: (65) 271-3566 Fax: (65) 271-3855
SHARP Electronic Components (Korea) Corporation RM 501 Geosung B/D, 541 Dohwa-dong, Mapo-ku Seoul 121-701, Korea Phone: (82) 2-711-5813 ~ 8 Fax: (82) 2-711-5819
CHINA
HONG KONG
SHARP Microelectronics of China (Shanghai) Co., Ltd. 28 Xin Jin Qiao Road King Tower 16F Pudong Shanghai, 201206 P.R. China Phone: (86) 21-5854-7710/21-5834-6056 Fax: (86) 21-5854-4340/21-5834-6057 Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp
SHARP-ROXY (Hong Kong) Ltd. 3rd Business Division, 17/F, Admiralty Centre, Tower 1 18 Harcourt Road, Hong Kong Phone: (852) 28229311 Fax: (852) 28660779 www.sharp.com.hk Shenzhen Representative Office: Room 13B1, Tower C, Electronics Science & Technology Building Shen Nan Zhong Road Shenzhen, P.R. China Phone: (86) 755-3273731 Fax: (86) 755-3273735
DataSheet 4U .com

▲Up To Search▲

Price & Availability of LQ065T5AR01

	To Download LQ065T5AR01 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .